Planet 1-Port Ultra PoE to 4-Port 802.3af/at Gigabit PoE Extender


SKU: PTE-POE-E304
The Planet 1 port to 4 port PoE extender is easy to install.  Simple plug and play. It is used between a power source equipment (PSE) and a powered device (PD). The POE-E304 injects power to the PD without affecting the data transmission performance. 

The POE-E304 offers a cost effective and quick solution to doubling the standard range of PoE from 100 to 200m. The extender is designed in a compact box containing five RJ45 ports, of which one "PoE IN" port functions as PoE (Data and Power) input and the other four "PoE OUT" ports function as PoE output. 

The "PoE OUT" port is also the power injector that transmits DC voltage over the Cat5/5e/6 cable and transfers data and power simultaneously between the PSE and PD.

Physical Port

  • 5-port 10/100/1000BASE-T Gigabit RJ45 interface
  • 1 port data + power input
  • 4 port data + power output

Power over Ethernet

  • 1 port data + power input
  • Complies with ultra Power over Ethernet end span and mid span PD
  • Complies with IEEE 802.3at Power over Ethernet Plus end span / mid span PD
  • Supports PoE input power up to 60W
  • 4 port data + power output
  • Complies with IEEE 802.3af/IEEE 802.3at Power over Ethernet end-span PSE
  • Up to 4 IEEE 802.3af/802.3at devices powered
  • Supports PoE power up to 30.8 watts for each PoE port
  • Auto detects powered device (PD)
  • Extends the range of PoE to an additional 100m (328ft.)
  • Forwards both Ethernet data and PoE power to remote device

Layer 2 Features

  • Hardware based 10/100/1000Mbps auto-negotiation and auto MDI/MDI-X
  • Integrates address look up engine, supporting 2K absolute MAC addresses
  • 9K Jumbo packet support
  • IEEE 802.1Q VLAN transparency
  • Features Store and Forward mode with wire speed filtering and forwarding rates
  • IEEE 802.3x flow control for full duplex operation and backpressure for half duplex operation
  • Automatic address learning and address taging

Case and Installation

  • No external power cable installation required
  • Made of metal for a desktop size design
  • Wall-mountable. Plug and- play installation
  • 0 - 50°C operating temperature
     
Network ConnectorPoE In Port
1 x 10/100/1000BASE-T Ethernet with Ultra PoE “Data + DC” in, auto MDI/MDI-X, auto-negotiation RJ45 connector

PoE Out Port
4 x 10/100/1000BASE-T Ethernet with IEEE 802.3at/802.3af PoE “Data + DC” out, auto MDI/MDI-X, auto-negotiation RJ45 connector
Data Rate10/100/1000Mbps
Switch ArchitectureStore-and-Forward
MAC Address Table2K
Data Buffer2Mbits
Switch Fabric10Gbps
Switch Throughput7.44Mpps @ 64 bytes
Jumbo Frame9K
Flow ControlIEEE 802.3x pause frame for full duplex
Back pressure for half duplex
LED IndicatorsPoE In Port
10/100 LNK/ACT (Orange), 1000 LNK/ACT (Green)
PoE Out Port 1 to Port 4
10/100 LNK/ACT (Orange), 1000 LNK/ACT (Green)
PoE-in-Use (Orange)
PoE Max. (Orange)
ProtectionESD (Ethernet): 6KV
Surge (EFT for power): 2KV
EnclosureMetal
InstallationDesktop/Wall mountable
Dimensions (W x D x H)160 x 92.5 x 28 mm
Weight370g
Power RequirementsPoE In: IEEE 802.3bt or 4-pair 802.3at PoE+ compliant with voltage within 50V-56V DC
External DC: 50~56V DC
Power Consumption4 watts/13.7BTU (System on with PoE input)
6 watts/20.6BTU (Ethernet full loading without PoE function)
60 watts/205.9BTU (Full loading with PoE function)
Network Cable10BASE-T: 4-pair UTP Cat5 up to 100m (328ft)
100BASE-TX: 4-pair UTP Cat5 up to 100m (328ft)
1000BASE-T: 4-pair UTP Cat5e, 6, up to 100m (328ft)
EIA/TIA-568 100-ohm STP (100m, 328ft)
OperatingTemperature: 0 ~ 50 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)
StorageTemperature: -10 ~ 70 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)